Looking for:
- How to release air brakes manually |
How to release air brakes manually
In certain emergency situations, like when an air brake system failure has occurred and you need to move your truck to a safe position, you may need to manually release the brakes to enable the vehicle to be moved. However, before we get into this technical advice article, it is extremely important to understand that when a spring brake is manually released that particular brake will not function and that wheel will have no braking force at all.
Related reading: Advice: What's a Jake brake? New product: Bendix rotor wipes New product: Bendix brake pad app. But first things first — what are spring brakes and what do they do? Heavy vehicle spring brakes are designed to provide two separate functions. One is to activate in an emergency if your service brakes fail and secondly to act as park brakes for parking the vehicle. Regulations dictate that all vehicles with air brake systems must have a means of stopping the vehicle if the service brakes the air system fails.
Most heavy truck manufacturers combine this function of the emergency braking system with a parking brake system using spring brakes. Unlike service brakes, spring brakes are not air applied. They only apply when air pressure leaves the spring brake chamber, causing the large spring to expand that in turn forces the brake shoe firmly against the brake drum.
They will only release when enough air pressure builds up inside the brake chamber to compress the spring. Spring brakes use a separate brake chamber from the service brakes. The '24' refers to the size of the service brake chamber and the '30' refers to the size of the spring brake chamber.
To accommodate the large coil spring, a section is added to the service brake chamber that is clearly visible and adds significantly to its size. This spring brake section is 'piggy-backed' onto the service brake section and these two sections function as two separate chambers.
The portion nearest the pushrod end is the service brake section and it works in the same manner as a separately mounted service brake chamber. When the brake's spring is 'caged' or compressed the brake is in the released state and will require a delivery of air pressure from the brake pedal to apply. That is why it is important to ensure that both the primary and secondary brake systems are fully charged to 90 to psi to kPa before driving the vehicle. A word of caution about servicing spring brakes: don't!
Don't service them for two reasons. Firstly as the large coil spring used in the brake chamber is compressed under very high tension, it is extremely difficult to release the tension safely let alone reinstall it once it's apart. Therefore, it's not only cheaper to replace a faulty chamber with a new one, it's far safer too.
It's not unheard of to find yourself stranded with a wheel that's locked up because the brakes have jammed. Chances are you'll be stuck on a lonely road, way out the back blocks, miles from phone range and any chance of getting a callout vehicle to come to the rescue. The good news is, if you've read this article this far, you'll now know you've got a reasonable understanding of how the brakes on your truck function and you'll be able to get yourself rolling again without too much fuss.
Once you have identified which wheel or axle has locked up, you need to slide under the vehicle and remove the dust plug on that faulty wheel or axle's spring brake chamber. Remove the release bolt assembly from the side pocket. To do this remove the release nut and washer from the release bolt, then slide the release bolt out of the holder. Clean the threads along the length of the release bolt as this will make it easier to tighten the nut later. Insert the release bolt through the opening in the rear of the spring chamber where the plug was removed, inserting it into the pressure plate.
Turn the release bolt a quarter turn clockwise in the pressure plate. This secures the cross pin into the cross-pin area of the pressure plate and locks it into the manual release position. With a spanner, turn the release bolt assembly nut until the compression spring is per cent caged. You will find that the nut is hard to wind because you are manually compressing the high tension spring. While doing this, check to make sure the pushrod adapter push rod or service push rod is retracting.
Now the brake is mechanically 'caged', the brake will not function. Extreme care should be used when moving a vehicle with the brakes in the 'caged' position.
Again, we cannot emphasise enough that this procedure should only be used in the case of an emergency. The brake system will need to be repaired by an authorised service center at the earliest opportunity.
Editorial prices shown are a "price guide" only, based on information provided to us by the manufacturer. Pricing guide current at the time of writing editorial. When purchasing a vehicle, always confirm the single figure price with the seller. If the price does not contain the notation that it is "Drive Away No More to Pay", the price may not include additional costs, such as stamp duty and other government charges.
Opinions expressed within trucksales. These Ads will be marked 'Sponsored'. Learn More. Become a trucksales member and get the latest news, reviews and advice straight to your inbox. Create an ad Manage my ad Safer selling Become a Dealer. International marketplaces Soloautos Chileautos Encar Webmotors. Recent Notifications. Howard Shanks -. Assemble the release bolt washer and nut on the release stud. Written By. Howard Shanks.
Disclaimer In most cases, trucksales.
No comments:
Post a Comment